Metal Processors has an extensive range of hard metal ancillaries; ranging from underlays, stainless steel clips and nails to roofing hand tools and bending, folding and profiling machinery.

UNDERLAYS

BEVENT SK

bevent sk.jpg

The advantages of BEVENT SK
• Can be installed under all types of metal coverings
• Installation possible on low pitch roofs due to high water draining capacity
• Reduced installation times due to the roll width of 1.40m
• 10 cm overlap provided on edges
• Effective and strong bonding of the sheeting by self-adhesive tape
• BEVENT provides a smooth surface an any substrate
• Suitable for all types of substrate

BEVENT SK is fast and easy to handle
•  Simple and reliable connection in valley and arris areas
•  Easily installed around penetrations
•  Secure adhesion of the wire mat with the contact layer but can also be separated without the use of tools
• Easy separation of the wire mat from the membrane by secure bonding of the two layers over the entire area at the same time

BEVENT M15

BEVENT M Roof Underlay Membranes provide reliable protection against moisture. BEVENT M are three-part underlay membranes for metal roofs. When exposed to the elements during construction and during actual use, BEVENT M protects the roof structure and thermal insulation from moisture caused by condensation, rain and fine snow.
BEVENT M underlay membranes are remarkable for their high water-vapour permeability. This ensures that humidity inside the structure diffuses through to the outside and that the roof structure and roof insulation are effectively protected from the harmful effects of condensation.

The light weight of the rolls and the stability of the material makes it easy to handle on the construction site. BEVENT M is easy to cut and quick to lay on the roof. BEVENT M15SK is manufactured with a self-adhesive tape to make the installation even easier.

ROOFING HANDTOOLS

OFFSET CUTTING SNIPS

Stainless steel, compound leverage, for stainless steel sheets, HRc 58-60

01290240 right LG / W: 9,45''/3,15'0,86 lb

01291240 left LG / W: 9,45''/3,15'0,86 lb

OFFSET CUTTING SNIPS II

Stainless steel, compound leverage, for stainless steel sheets, HRc 65

01295260 right LG / W: 10,24''/3,15'1,15 lb

01295261 left LG / W: 10,24''/3,15'1,15 lb

SEAMING PLIERS I

Straight, lap joint

01100081jaw W 3,15 inch LG / W: 12,60''/2,95''1,87 lb

 

SEAMING PLIERS II

Bent of 45ø, lap joint

01090040 jaw W 1,57 inchLG / W:10,24'' / 1,57''1,32 lb

01090060 jaw W 2,36 inchLG / W: 10,5''/2,36'''1,54 lb

01090080 jaw W 3,15 inch LG / W: 11,81''/3,15''2,04 lb

SEAMING PLIERS - TONGS

Straight, lap joint

01141120jaw D 4,9'', W 4,72''LG / W: 19,29'' / 4,72''4,08 lb

01141140jaw D 4,9'', W 5,51''LG / W: 19,29'' / 5,51''4,30 lb

01141160jaw D 6,9'', W 6,30''LG / W: 22,05'' / 6,30''6,61 lb

 

01141180jaw D 6,9'', W 7,09''LG / W: 22,05'' / 7,09''7,50 lb

01141200jaw D 7,3'', W 7,87''LG / W: 22,44'' / 7,87''7,17 lb

TINMANS HAMMER

PCV, edged

01674000LG / W:14,37'' / 5,91''19,4 oz

 

HAMMER FOR ANGLE FLAT SCRAPER

Polished

01121000LG / W:12,5'' / 4,5''10,58 oz

 

TWINSEAM FOLDER 112DPF

This tool makes a manual accurate lock-seam just by spreading the levers. 
Dosed application of weight onto the implement relieves strain from the arms. 
Cost saving of the twinseam-folder is without competition working small roof-areas and corner-constructions.
The implement is in dependent of any current source. Its application starts at a 11/2"-2"seam height. Durable baked epoxy finish

01121000LG / W:12,5'' / 4,5''10,58 oz

 

SQUARESEAM FOLDER 111 WFSCH

This manually operated squareseamfolder joins SPM 30/80 profiles, smooth
lead-on avoid marks at the transitions. It is easy to handle when working extreme angular sheating, the tool may also be used for vertical as well as for horizontal beads. Durable baked epoxy finish.

91100000tool W: 8 2/3, claw H: 2''LG / W:14,96'' / 8,66''4,41 lb

 

DOUBLE WELT IRON

Steel forged, prism height 0,98” and 1,38”

01110000LG / W:9,45'' / 5,52''7,51 lb

 

SQUEEZING FOLDING PLIER

Forged of special steel, depth 5,51”

01130000LG / W:9,06'' / 8,66''1,88 lb

SOLDERING IRON

Technical details: A circular flame surrounds the soldering iron tip which causes a quick warming up as well as a reduced gas consumption, soldering iron tip: 360° turnable, inclination angle adjustable by 10°, available in 4 models, metal bow: adjustable in 2 positions, with spring lock - with Piezo ignition and rotational tube connection
- 100% windprotection through combustion chamber
- immediately ready for use through a new burning technique; the working temperature is reached after 1 minute
- turnable tube makes an easy handling possible
- armoured piezo-system with approx. 50 000 ignitions
and 2 years warranty
- GS / TÜV homologated

66434000 LG/W:14,37'' / 4,33''2,08 lb

ROOFING MACHINERY

Since 1948 the Jouanel company produces machines and equipments for the work of metal in sheets.

These machines and equipments are intended in particular for the companies specialized in roofing, in roof framing and sheet metal work, in aluminium joinery work, in metal millwork, as well as for the companies specialized in metalworking, in building hardware, in metal roof framing,
 

Cutting and Guillotine Machines
Download PROBAC HT Brochure
 

 

 

Folding Machines
Download PCX 2040 Brochure
 

 

 

Standing Seam Machine
Download PCB 651 Brochure

 

 

Long Strip Roofing Machines
Download Brochure